Require two-step verification and set lockout rules
Este conteúdo não está disponível em sua língua ainda.
Two-step verification asks for a 6-digit code from an authenticator app after the password. In Settings › System › Authentication you decide who must use it, and how long an account locks after too many wrong passwords. Both apply to signing in with an email address and password. People who sign in with single sign-on get your identity provider’s protections instead.
Choose who must use two-step verification
Section titled “Choose who must use two-step verification”-
Turn on admin mode: select your name in the top bar, then Elevate to Admin.
-
Select Settings in the menu bar, open System, then the Authentication tab.
-
Choose an MFA Policy, then select Save changes in the bar at the bottom of the page.
| Option | Who must use two-step verification |
|---|---|
| Optional (users choose) | Nobody. Anyone can turn it on for themselves under Sign-in security. This is the default. |
| Required for Admins and HR Admins | People who hold the Admin or HR Admin role, directly or through a group. Admins need it whether or not they’re in admin mode. Custom roles aren’t included, even ones built on HR Admin. |
| Required for everyone | Everyone who signs in with a password. |
The policy takes effect within about a minute of saving.
What changes for people
Section titled “What changes for people”- People who must use it and haven’t set it up get Set up two-step verification the next time they sign in with their password, and can’t get in until they finish. See When your company requires it.
- People it applies to who are signed in with a password but didn’t enter a code are asked to sign in again within about 15 minutes.
- People who already use it see no change, except that they can’t remove their only authenticator any more. See Manage your sign-in security.
- People who sign in with single sign-on are never asked for an Anima HR code.
Going back to Optional (users choose) doesn’t turn off anyone’s two-step verification: people who set it up keep using it until they remove it themselves.
Reset someone’s two-step verification
Section titled “Reset someone’s two-step verification”When someone has lost both their authenticator and their recovery codes, an Admin can remove them so the person can sign in with their password alone.
-
Turn on admin mode, select Settings in the menu bar, open Access, then the Users & Groups tab.
-
Search for the person by name or email, and select them in the list.
-
Under Two-step verification, select Reset two-step verification, then select Reset two-step verification again to confirm.
Two-step verification reset for and the person’s name confirms it. Their authenticators and recovery codes are gone, and they’re signed out on every device. They sign in with their password, and set up two-step verification again at that sign-in if the MFA Policy requires it for them.
- Two-step verification only shows for people who have it on, and never for yourself: another Admin resets yours.
- HR Admins may reset two-step verification for people who aren’t Admins or HR Admins, but the button is in Settings › Access, which HR Admins can’t open. Ask an Admin.
Lock accounts after wrong passwords
Section titled “Lock accounts after wrong passwords”Brute-Force Protection, at the bottom of the Authentication tab, locks an account for a while after too many wrong passwords in a row.
| Setting | What it does | Default |
|---|---|---|
| Lockout Threshold (failed attempts) | How many wrong passwords lock the account. | 5 |
| Lockout Durations (seconds) | How long each lockout lasts, in seconds, in the order listed: the first lockout uses the first duration, the second lockout the next one, and so on. Past the end of the list, every lockout uses the last duration. To add one at the end, type it in Add duration (seconds)… and select + Add. Select × on a duration to remove it; when only one is left, it stays. | 60, 300, 900, 1800 (1, 5, 15 and 30 minutes) |
How it works today:
- Wrong passwords count until the person signs in with the right one, or until the account locks. The count doesn’t run out with time.
- The lockouts never start over: Anima HR counts an account’s lockouts for as long as it exists. With the default durations, every lockout from the fourth one on lasts 30 minutes.
- During a lockout, the sign-in page shows Too many attempts. Please wait and try again. The person can wait, or reset their password, which ends the lockout. Admins can’t unlock an account. See If your account is locked.
- Wrong two-step verification codes have their own limit, which you can’t change: after 5 wrong codes, the person waits 5 minutes.
How long people stay signed in
Section titled “How long people stay signed in”These times are fixed: there are no settings for them.
| What | How long |
|---|---|
| Staying signed in on a browser | Until the person logs out, or until they haven’t used Anima HR on that browser for 7 days. There’s no maximum, so someone who uses Anima HR at least once a week stays signed in. The same applies after single sign-on. |
| Renewing the sign-in | Every 15 minutes, in the background, while the person uses Anima HR. Changes that end a sign-in, such as requiring two-step verification, take effect at the next renewal. |
| The code step after the password | 5 minutes |
| Setting up two-step verification at sign-in | 10 minutes |
| A password reset link | 1 hour |
| An invitation link | 7 days |
To sign someone out on every device, reset their two-step verification (if they have it on). People can sign themselves out everywhere by resetting their password.
Can’t see this?
Section titled “Can’t see this?”- Settings has no System or Access card. Turn on admin mode.
- HR Admins don’t see the System card. Changing Authentication needs Manage authentication, which only Admins have, so the card isn’t shown to HR Admins.
Related
Section titled “Related”- Sign in: what people see when they set up and use two-step verification
- Choose how people sign in
- Set up single sign-on